Top
Proshop
Sponsors
News:
Visit the
Team Iceshanty Proshop
Home
Forum
Help
Login
Register
IceShanty.com's Ice Fishing Community
»
Ice Fishing Tips -Check your local regulations!
»
Equipment
(Moderator:
Bean
) »
my diy ice auger attacment
Print
Pages: [
1
] |
Go Down
Author
Topic: my diy ice auger attacment (Read 2683 times)
Ahrenv
IceShanty Rookie
Posts: 7
my diy ice auger attacment
«
on:
Sep 26, 2011, 11:03 AM »
couple of little things from menards and all set to go. neighbor guy welded it up for me... may be 10 bucks into it....
couple of bolts. a outlet cover. rubber bungiee. and a old drill bit. boom.
Logged
Idahogator
Team IceShantyholic
Posts: 7,938
Muckeltonian Society
Re: my diy ice auger attacment
«
Reply #1 on:
Sep 26, 2011, 01:17 PM »
Welcome Ahrenv.
This sounds as if you've invented something which some of us would like to see.
Picture posting to this site can't be done.
Go to PhotoBucket.com, put your pics there and post only the IMG code here and it'll work.
Logged
Ahrenv
IceShanty Rookie
Posts: 7
Re: my diy ice auger attacment
«
Reply #2 on:
Sep 26, 2011, 01:51 PM »
attempt number two. hopefully that works.
Logged
rugby ice
Team IceShanty Regular
Posts: 269
Re: my diy ice auger attacment
«
Reply #3 on:
Sep 26, 2011, 02:00 PM »
I'm asking to clarify why have the outlet cover on? Is it so you don't drill one hole and send the bit down the new drilled hole? Nice set up. How do you get it so true w/ the auger attached so it doesn't wabble when drilling?
Logged
http://
Ahrenv
IceShanty Rookie
Posts: 7
Re: my diy ice auger attacment
«
Reply #4 on:
Sep 26, 2011, 04:15 PM »
yes the outlet cover is on to hold against that other nut thats welded on. thats on there just in case i have to back the auger. that way i don't lose the the set up. My other option was to put a long screw to stick out the side of the 'bit'. that way if it does fall off it will hopefully catch on the ice.... as of getting true. i wasn't to worried on being as true as possible. i figured when i do it by hand i wobble a bit... same on the power auger. ... just a prototype, i would have like it to have been a bit shorter, but with this length i wont need to bend over to much. i might have rambled a bit. other wise its just a rod over to 5/8's fine thread bolts. i want to say its a mora 7".
outlet cover:
http://www.johnstonesupply.com/storefront/supplies/electrical-installation-maintenance-supplies/wall-plates-covers/supplies/electrical-installation-maintenance-supplies/wall-plates-covers//prodg32-179.html
the two bolts were threaded on the auger... then tacked up, that way they are one.
bolt:
http://www.menards.com/main/tools-hardware/fasteners/nuts/hex/5-8-18-fine-hex-nuts-grade-5/p-1640911-c-8915.htm
the drill bit was a old wood boring/spade bit:
http://www.menards.com/main/tools-hardware/power-tool-accessories/drill-bits/3-4-spade-bit/p-1465799-c-10079.htm
Hope that helps.
Logged
beeverfishing
Team IceShanty Maniac
Posts: 2,009
Re: my diy ice auger attacment
«
Reply #5 on:
Sep 26, 2011, 04:24 PM »
Looks good... Let us know how it works for you on the ice...
Logged
Print
Pages: [
1
] |
Go Up
IceShanty.com's Ice Fishing Community
»
Ice Fishing Tips -Check your local regulations!
»
Equipment
(Moderator:
Bean
) »
my diy ice auger attacment
Iceshanty
|
MyFishFinder
|
MyHuntingForum
Contact
|
Disclaimer
|
Privacypolicy
|
Sponsor
© 1996- Iceshanty.com
All Rights Reserved.