Equipment Board Sponsor Eyoyo Underwater Cameras

Author Topic: Using 18V Drill Battery for LiveScope System  (Read 670 times)

Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Using 18V Drill Battery for LiveScope System
« on: Mar 08, 2019, 01:26 PM »
I bought a Garmin LiveScope system for my boat and have built a 'LiveScope Box' that is self contained. I've missed the boat for ice fishing this year, but I have big plans to use this LiveScope next year and beyond.  I hacked an old Ryobi battery charger and turned it into a device that outputs 18V.  I have my box built and am very pleased with it.  I am running the 'black box' and a EchoMap Plus 93sv off this ryobi battery.  I'm conducting a test in my basement with the livescope submerged in water while the unit runs on a 4ah battery.  I had planned to get the new 9ah battery Ryobi sells, but this 4ah battery has been running the entire system for 3 hours and the voltage is down to 17.2v according he the EchoMap.  I have no idea when this battery is considered 'discharged' and needs swapped out with a fresh one.  Can I run this until it gets in the range of 12v?  If I do that, will I ruin the battery?  I got the idea of using the cordless drill battery from this site, but am now realizing I don't really know at what point I should swap the battery based on volatage.  I'm sorry for jumping right in with a question like this on my first post.

Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Re: Using 18V Drill Battery for LiveScope System
« Reply #1 on: Mar 08, 2019, 02:02 PM »
The Garmin unit just shut itself down at around the 3 1/2 hour mark.  It looks like I should swap out batteries soon after voltage drops below 17.5 which would have been about 2.5 hours on a 4ah battery.  This tells me the amp draw is less than 2 at least when running with the LSV32 in a bucket of water.  This thing's going to be awecsome!  I added a picture of my box if anyone is interested.


Offline shoeshineman

  • IceShanty Rookie
  • **
  • Posts: 12
Re: Using 18V Drill Battery for LiveScope System
« Reply #2 on: May 05, 2019, 04:10 PM »
I am very interested in this! Can you show in detail how this battery is setup?

Thanks in advance!

-Josh

Offline Skywagon

  • Team IceShanty Regular
  • ***
  • Posts: 170
Re: Using 18V Drill Battery for LiveScope System
« Reply #3 on: May 06, 2019, 06:54 AM »
2-12 volt, 10 amp Lithium batteries wired parallel will last a day of fishing with the Livescope and the 93 screen on full bright.  Does your boat motor have a charging system you can plumb into?

Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Re: Using 18V Drill Battery for LiveScope System
« Reply #4 on: May 07, 2019, 10:00 AM »
I chose ryobi as my battery because I have a large selection of their batteries for my tools.  Once I go to a drill powered auger, it will be a ryobi drill. Anyway, I took an old charger base and took it apart. On the circuit board, I broke the pathways from the positive and negative battery to the rest of the circuitry. I then cut the power cord and soldered one side to the pathway tied to the positive side of the battery and soldered the other side to the negative. At this point I had converted the charger base to output 18v. I used this to provide power to the black box and head unit.

Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Re: Using 18V Drill Battery for LiveScope System
« Reply #5 on: May 07, 2019, 10:10 AM »
On my boat, I still use my ‘ice fishing box’. I wanted to be able to mount the transducer pole to either side of the boat.  And I wanted the head unit on the gunnel. When you ‘spot lock’ over fish, the bow will end up pointed into the wind, so to deal with that, I wanted my transducer pole to be track mounted. I have a tig welder and fabricated the mother of all transducer mounts. I used a Cisco electronics mount to gain the ability to swivel the pole from horizontal to vertical. Hey, it was winter so why not?





Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Re: Using 18V Drill Battery for LiveScope System
« Reply #6 on: May 07, 2019, 10:21 AM »
We fished western basin of Erie this past weekend. Regular sonar was marking fish from 20-25 down.  We caught a couple fish deep, but you can take your livescope, aim it forward with the range at 100 ft and see the true depth the fish in front of the boat are suspended at. You’ll track a target coming towards the boat then when it’s 30 feet from the boat it disappears. We saw suspended fish from 10-15 that we otherwise would not have known they were there and caught more fish because of this information.  This is huge and in my mind justifies the purchase. Those shallow fish are the most catchable and you never see them on regular sonar.

Offline Wyoming_Ice

  • Team IceShanty Maniac
  • **
  • Posts: 1,267
  • Ice Fishing God's Country "Big Wounderful Wyoming"
Re: Using 18V Drill Battery for LiveScope System
« Reply #7 on: May 13, 2019, 08:18 AM »
Did you have to install a "voltage regulator" to bring the voltage down to 12 volts for your Garmin unit ?
RIP "LT"   This place just won't be the same...

Offline dgfidler

  • IceShanty Rookie
  • **
  • Posts: 6
Re: Using 18V Drill Battery for LiveScope System
« Reply #8 on: May 13, 2019, 08:27 AM »
No, the echomap plus 93sv and livescope support up to 18vDC. Since a fully charged 18v battery is 20.2v, I was worried at first,  but I’ve got over 20 hours on the system at between 18 and 20v that I’m no longer concerned.

Offline papadarv

  • Team IceShanty Regular
  • ***
  • Posts: 135
Re: Using 18V Drill Battery for LiveScope System
« Reply #9 on: May 15, 2019, 09:21 AM »
Livescope /Echomap operating volts is 10vdc to 32vdc so your 18v Ryobi is well within the operating range. Ryobi uses Sanyo (Japan) 18650 Li-Ion batteries charged to 4.2v with a cut-out at 3.0v. 5 batteries in series provides the "typical" 18v with a cut-out at about 15v. The charge board inside the battery also has a shut down circuit at 15v preventing battery damage. Livescope uses 21 watt (@18 v  = 1.1amp) you should get about 4 hours on your 4ah battery. All the cordless tool batteries are great for fishing electronics. I use the Milwaukee M18 with a USB / 12v converter on my electronica as they operate at 12v. Drill holes with my 1200ip fuel than pop battery in converter running flasher, camera, charging phones etc. Your good to go with the Ryobi.






 



Follow Iceshanty at Twitter Iceshanty Facebook Page Iceshanty Youtube Channel
Iceshanty | MyFishFinder | MyHuntingForum
Contact | Disclaimer | Privacypolicy | Sponsor
© 1996- Iceshanty.com
All Rights Reserved.