Show me your sleds!!!

[michianafisherman]

My sleds are warm!

[TroutFarmer]

I retrofitted skis on this old Rubbermaid garden trailer with some custom brackets this afternoon.  It should work slick this winter...

[hulv]

OK here is what I have come up with in the off season     
the pics were from my phone   sorry if they suck



this is the "sled" or mortar mixing bucket I bought from the home depot. $11.99



here are the UHMW runners I put on it got em from EBay $19.00 for 10 pcs. I only used 4 of em so I have extras to replace them with I carefully laid it all out and everything is straight counterbored and even



well I like to be comfortable so I got a gamma seal lid $7.00 and attached a boat seat $35.00 to it I have found a short bucket to attach it to (hard to bend down....   something is in the way??? might have something to do with the BEER laughs the old lady while I am in full ice gear trying buckets in the livingroom)  the gamma seal ring stays on the bucket and I can remove the seat by spinning it on or off  and I have built in  waterproof storage for the electronics



and last I have a couple of kitty litter buckets freebie attached and a little shelf (freebie.... you laugh at me I am cutting up the cutting board) to hold my Joe and some bait and the such   the kitty litter buckets are just a hair larger than my fishing buckets so they don't get stuck together  (theres that d**n BEER)

just enough room behind the buckets for the auger....      I think this just might work.

I know I am not the only person in the offseason to make a sled   lets see them.

[rvz]

Nothing fancy.  Jet Sled SUV.  I carry a fold up chair to sit in.  Too old to sit on a bucket all day.

[Burl Ives]

[Dizzy]

Here’s my sled circa 2006… Jet Sled Jr. “pimped out” w/ PVC structure and Petty-blue plywood decks.



Kicking around a revised edition for the 09/10 season… I was trying to get the IS.com mod’s to start a new topic forum dedicated to custom built sleds or sled modifications… there are some really creative dudes on here and plenty of inspiration to draw from when the time comes to build.

[Madpuppy]

I like the sled Dizzy, is that a built in beer holder by the cooler?

[Dizzy]

I like the sled Dizzy, is that a built in beer holder by the cooler?

Ha ha, it could be!  

No, it holds my transducer when moving from hole-to-hole... it swings outboard the sled so the water doesn't drain into the sled (there is a 1" drain hole in the bottom of the pipe elbow there).

[Madpuppy]

Ha ha, it could be!  

No, it holds my transducer when moving from hole-to-hole... it swings outboard the sled so the water doesn't drain into the sled (there is a 1" drain hole in the bottom of the pipe elbow there).

Looks like you've thought of everything, it's a nice setup!

[bart]

I got a little inspiration on this site for my sled, thanks Dizzy.

[rlowery]

how much did all that pvc and fixtures run ya bart?

[Mainedog]

I "built" this ski/Thule roof rack sled a couple years ago.  I just shortened the skis so it fits my DX3000 a bit better.  Built from FREE curbside skis and a roof rack I inherited, and a bit of angle aluminum.  The roof rack pops off the skis by loosening the clamps.

[Mainedog]

Another project I've been working on over the summer.  I built a box to put on top of my JetSled XL out of 1/4" plywood and some 1/2"x1/2" pine framing.  My first experience with West Marine epoxy.  That was fun.  Some black paint, piano hinges.  Some aluminum stock
to for door edges.  One door opens by itself.  When you open the other one, it opens the second as well.  My XL has UHMW strips for wear protection on the bottom.  And I added an aluminum backer plate to the hitch eye-bolts for reinforcement. I also picked up a heavy duty two hitch for it.  The box weighs just a bit more than the sled itself.  My only regret is building it ~12" tall on the sides.  I think 9" would have been plenty.  I still need to add a cord to keep the door from falling all the way back. 
Sorry about the flash reflections in one of the pictures.

MD

[prchslyr]

Mainedog-Dou you need to recess the screws into the bottom of the ski's? Or is it not a big deal?

[Mainedog]

Mainedog-Dou you need to recess the screws into the bottom of the ski's? Or is it not a big deal?

Yes.  I used machine screws and counter-sunk them.  They are slightly sunk (i.e. deeper than flush to the plastic).

[prchslyr]

Yes.  I used machine screws and counter-sunk them.  They are slightly sunk (i.e. deeper than flush to the plastic).

Thanks man. I'm going to try pimping my jet sled out tomorrow. I've got access to old ski's free wood and pvc and tools. I'm just not all that handy. Wish me luck. I'll be sure to post pics once my old lady finds the darn camera cord. I want to go totally nuts with it but can only do what I'm capable of. Any lil tidbits you can throw my way would be a big help. It will probably be something I'll always be messing with so I'm sure I won't be happy after one day.