Top
Proshop
Sponsors
News:
Visit the
Team Iceshanty Proshop
Home
Forum
Help
Login
Register
IceShanty.com's Ice Fishing Community
»
Ice Fishing Tips -Check your local regulations!
»
Equipment
»
Ice Augers
(Moderator:
Bean
) »
Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy
The Iceshanty Ice Auger Board is sponsored by
Print
Pages: [
1
] |
Go Down
Author
Topic: Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy (Read 2797 times)
TenE307
IceShanty Rookie
Posts: 82
Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy
«
on:
Jan 29, 2013, 02:17 PM »
Hello, Looking for input before I tear into my machine. Its been a tough start to the season with me and my auger. First off is I bought it used last year, so I dont know how It been treated. When I got it it needed a carb cleaning. Noticed the throttle linkage was broken and wire was used to fix that. Last year I ran it dry to store it and fogged the cylinder. This year tried to start it with no luck. Found the gasket was dry and had no movement. Bought a gasket set and fixed that. Seems to be still letting too much gas by so Im going to have to adjust the spring and needle. I dont have the luxory of high and low mixture screws. So after I got it running good in the garage I took it out this weekend for its first true runs. Seemed to be a little weak in the torque area. I wasnt putting any weight to it and it would quit turning. Got almost to the point on my fifth hole to where it would barely turn as soon as it hit the ice. When I got home this is what I found:
Logged
Gambler
Team IceShanty Regular
Posts: 451
Ice Fishing Rulez!
Re: Eskimo Barracuda Spewing Grease
«
Reply #1 on:
Jan 30, 2013, 01:42 PM »
I would say that someone has put too much grease in the gear housing or the seal is bad. I will bet that you got grease on the clutch and that is why the auger stops turning. Time to tear into it.
Logged
Take Care and God Bless
Rick
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #2 on:
Jan 30, 2013, 06:28 PM »
I am in the process. Does anybody know how to remove the centrifugal clutch?
Logged
lil maggot
Iceshanty Militia
Team IceShanty Addict
Posts: 719
What better is there to do in the winter?
Re: Eskimo Barracuda Spewing Grease
«
Reply #3 on:
Jan 30, 2013, 06:38 PM »
You will need to hold the flywheel and without a special spanner wrench that most used. you will have to tap the clutch in the direction of the arrow. Be careful not to damage the clutch drum.
oooops sorry, this is gambler signed in under my son lil maggot.
Logged
Ice fishing line of fire ENGAGE!
Gambler
Team IceShanty Regular
Posts: 451
Ice Fishing Rulez!
Re: Eskimo Barracuda Spewing Grease
«
Reply #4 on:
Jan 30, 2013, 06:42 PM »
Was the top seal bad or did someone pack the gears full of grease?
Logged
Take Care and God Bless
Rick
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #5 on:
Jan 30, 2013, 06:50 PM »
Thank you! Im not sure yet for the reason of grease. Probably too much put in.
Logged
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #6 on:
Jan 30, 2013, 07:03 PM »
Got it off. Had to put a screw driver in the fly wheel and tap with a screw driver on the clutch. Now what is the best thing to clean grease out?
Logged
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #7 on:
Jan 30, 2013, 08:46 PM »
Im trying to clean out all the grease in the gears and not sure how to remove the gears. Any help would be great. Thank you!
Logged
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #8 on:
Jan 30, 2013, 09:50 PM »
Got the gears out! Had to just wiggle them out a little.
Logged
Gambler
Team IceShanty Regular
Posts: 451
Ice Fishing Rulez!
Re: Eskimo Barracuda Spewing Grease
«
Reply #9 on:
Feb 01, 2013, 06:32 AM »
Did ya get it back together?
What exactly was the problem?
Logged
Take Care and God Bless
Rick
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease
«
Reply #10 on:
Feb 01, 2013, 08:41 AM »
Plan on putting it back together tonight or this weekend. Got some Green grease from advanced auto rated to -20 last night. Sure get a funny look when you go into a parts store and ask for their coldest rating grease. Not sure what the problem was other than too much grease. All the componets inside look good. The only thing that might have caused it was I was having my carb leak before I got the gasket set and might have got some in the gears and made the grease not as thick. So far I have filled 2 grocery bags with greasy paper towels and q-tips with more to clean. I dont know If ill be able to test it under load because our ice is starting to fade quick and next week is supposed to be in the 60's.
Logged
TenE307
IceShanty Rookie
Posts: 82
Re: Eskimo Barracuda Spewing Grease (updated FIXED) Pic heavy
«
Reply #11 on:
Feb 05, 2013, 12:24 PM »
Got it back together all nice and cleaned. Seams like it is working better but will need to test on the ice.
Before:
After cleaning:
Adding grease:
Clutch cleaned and assembled:
That grean grease is like working with stringy snot! It seams a little thick but auger turns fine once warmed up. Havent had any really cold temps to test it on yet.
Thanks for everyones help! I hope the pics help others!
Logged
Gambler
Team IceShanty Regular
Posts: 451
Ice Fishing Rulez!
Re: Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy
«
Reply #12 on:
Feb 05, 2013, 07:28 PM »
Good deal !!!!
Logged
Take Care and God Bless
Rick
wigginzoid
IceShanty Rookie
Posts: 3
Re: Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy
«
Reply #13 on:
Apr 07, 2013, 03:09 PM »
How did you get the clutch drum off the top of the transmission?
Logged
Print
Pages: [
1
] |
Go Up
IceShanty.com's Ice Fishing Community
»
Ice Fishing Tips -Check your local regulations!
»
Equipment
»
Ice Augers
(Moderator:
Bean
) »
Eskimo Barracuda Spewing Grease (updated FIXED) pic heavy
Iceshanty
|
MyFishFinder
|
MyHuntingForum
Contact
|
Disclaimer
|
Privacypolicy
|
Sponsor
© 1996- Iceshanty.com
All Rights Reserved.